Low Latency 40G Ethernet Intel® FPGA IP User Guide: Agilex™ 5 FPGAs and SoCs

Download PDF
ID 813652
Date 4/01/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the Low Latency 40G Ethernet Intel® FPGA IP 2. Low Latency 40G Ethernet Intel® FPGA IP Parameters 3. Getting Started 4. Functional Description 5. Clocking and Reset Requirements 6. Interfaces and Signal Descriptions 7. Control, Status, and Statistics Register Descriptions 8. Comparison Between Various Low Latency 40G Ethernet Intel® FPGA IPs 9. Document Revision History for Low Latency 40G Ethernet Intel® FPGA IP User Guide: Agilex™ 5 FPGAs and SoCs
1. About the Low Latency 40G Ethernet Intel® FPGA IP x
1.1. Low Latency 40G Ethernet Intel® FPGA IP Supported Features 1.2. Low Latency 40G Ethernet Intel® FPGA IP Device Family and Speed Grade Support 1.3. Resource Utilization 1.4. Release Information
1.2. Low Latency 40G Ethernet Intel® FPGA IP Device Family and Speed Grade Support x
1.2.1. Low Latency 40G Ethernet Intel® FPGA IP Device Family Support 1.2.2. Low Latency 40G Ethernet Intel® FPGA IP Device Speed Grade Support
3. Getting Started x
3.1. Introduction to Intel® FPGA IP 3.2. Installing and Licensing Intel® FPGA IPs 3.3. Specifying the IP Parameters and Options 3.4. Simulating the IP 3.5. Generated File Structure 3.6. Integrating Your IP in Your Design 3.7. Testbench 3.8. Compiling the Full Design and Programming the FPGA
3.6. Integrating Your IP in Your Design x
3.6.1. Pin Assignments 3.6.2. Placement Settings
3.7. Testbench x
3.7.1. Understanding the Testbench Behavior
4. Functional Description x
4.1. Low Latency 40G Ethernet Intel® FPGA IP Functional Description 4.2. GTS Transceiver Configuration 4.3. TX MAC Datapath 4.4. RX MAC Datapath 4.5. Flow Control 4.6. Frame Status Checking 4.7. Link Fault Signaling Interface
4.3. TX MAC Datapath x
4.3.1. Preamble Pass-through/Insertion 4.3.2. Padding Bytes Insertion 4.3.3. Deficit Idle Count 4.3.4. TX CRC Insertion/Passthrough 4.3.5. TX Avalon® Streaming Filter 4.3.6. TX PCS 4.3.7. PMA
4.4. RX MAC Datapath x
4.4.1. RX Preamble Pass-through or Removal 4.4.2. RX CRC Checking and Dynamic Option to Forward 4.4.3. Strict SFD/Preamble Checking 4.4.4. RX PCS Functional Description
4.5. Flow Control x
4.5.1. TX Pause/PFC Flow Control Transmission 4.5.2. XON/XOFF Pause Frames
4.6. Frame Status Checking x
4.6.1. Frame Type Checking 4.6.2. Length Checking
5. Clocking and Reset Requirements x
5.1. Reset Requirements
6. Interfaces and Signal Descriptions x
6.1. TX MAC Interface to User Logic 6.2. RX MAC Interface to User Logic 6.3. GTS Transceivers Signals 6.4. GTS Transceiver Reconfiguration Signals 6.5. Avalon® Memory-Mapped Management Interface 6.6. Miscellaneous Status and Debug Signals 6.7. Reset Signals 6.8. Clocks 6.9. Flow Control Interface 6.10. GTS Reset Sequencer Intel® FPGA IP
7. Control, Status, and Statistics Register Descriptions x
7.1. PHY Registers 7.2. TX MAC Registers 7.3. RX MAC Registers 7.4. Pause/PFC Flow Control 7.5. Statistics Counters 7.6. Shadow Register
1. About the Low Latency 40G Ethernet Intel® FPGA IP
2. Low Latency 40G Ethernet Intel® FPGA IP Parameters
3. Getting Started
4. Functional Description
5. Clocking and Reset Requirements
6. Interfaces and Signal Descriptions
7. Control, Status, and Statistics Register Descriptions
8. Comparison Between Various Low Latency 40G Ethernet Intel® FPGA IPs
9. Document Revision History for Low Latency 40G Ethernet Intel® FPGA IP User Guide: Agilex™ 5 FPGAs and SoCs

3.5. Generated File Structure

The Quartus® Prime Pro Edition software generates the following output files for Low Latency 40G Ethernet Intel® FPGA IP for Agilex™ 5 devices.
Figure 4. IP Generated Files
Table 10.  IP Generated Files

File Name

Description

<your_ip>.ip

The Platform Designer system or top-level IP variation file. <your_ip> is the name that you give your IP variation.

<your_ip>.cmp The VHDL Component Declaration (.cmp) file is a text file that contains local generic and port definitions that you can use in VHDL design files.

This IP does not support VHDL. However, the Quartus® Prime Pro Edition generates this file.

<your_ip>.html

A report that contains connection information, a memory map showing the address of each slave with respect to each master to which it is connected, and parameter assignments.

<your_ip>_generation.rpt IP or Platform Designer generation log file. A summary of the messages during IP generation.
<your_ip>.qgsimc Lists simulation parameters to support incremental regeneration.
<your_ip>.qgsynthc Lists synthesis parameters to support incremental regeneration.
<your_ip>.qip

Contains all the required information about the IP component to integrate and compile the IP component in the Quartus® Prime Pro Edition software.

<your_ip>.csv Contains information about the upgrade status of the IP component.

<your_ip>.bsf

A Block Symbol File (.bsf) representation of the IP variation for use in Quartus® Prime Block Diagram Files (.bdf).

<your_ip>.spd

Required input file for ip-make-simscript to generate simulation scripts for supported simulators. The .spd file contains a list of files generated for simulation, along with information about memories that you can initialize.

<your_ip>_bb.v You can use the Verilog black-box (_bb.v) file as an empty module declaration for use as a black box.
<your_ip>_inst.v or _inst.vhd HDL example instantiation template. You can copy and paste the contents of this file into your HDL file to instantiate the IP variation.

This IP does not support VHDL. However, the Quartus® Prime Pro Edition generates the _inst.vhd file.

<your_ip>.v HDL files that instantiate each submodule or child IP for synthesis or simulation.
mentor/

Contains a ModelSim* script msim_setup.tcl to set up and run a simulation.

aldec/

Contains a Riviera-PRO* script rivierapro_setup.tcl to setup and run a simulation.

This IP does not support simulation with the Riviera-PRO* simulator. However, the Quartus® Prime Pro Edition software generates this directory.

synopsys/vcs/

synopsys/vcsmx/

Contains a shell script vcs_setup.sh to set up and run a VCS* simulation.

Contains a shell script vcsmx_setup.sh and synopsys_ sim.setup file to set up and run a VCS* MX simulation.

cadence/

Contains a shell script ncsim_setup.sh and other setup files to set up and run an NCSim simulation.

submodules/ Contains HDL files for the IP submodule.
<child IPs>/ For each generated child IP directory, Platform Designer generates synth/ and sim/ sub-directories.

For information about the file structure of the design example, refer to the Low Latency 40G Ethernet Intel® FPGA IP Design Example User Guide: Agilex™ 5 FPGAs and SoCs .

Related Information
Level Two Title