Intel® Stratix® 10 MX FPGA Development Kit User Guide

Download PDF
ID 683867
Date 6/15/2020
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Development Kit Components 5. Board Test System A. Additional Information B. Revision History
1. Overview x
1.1. General Development Kit Description 1.2. Recommended Operating Conditions 1.3. Handling the Development Kit
2. Getting Started x
2.1. About the Intel® Quartus® Prime Software 2.2. Development Kit Package 2.3. Installing the Intel FPGA Download Cable Driver
3. Development Kit Setup x
3.1. Applying Power to the Development Kit 3.2. Default Switch and Jumper Settings
4. Development Kit Components x
4.1. Components Overview 4.2. Intel® MAX® 10 FPGA System Controller 4.3. Intel® MAX® 10 FPGA Power Manager 4.4. FPGA Configuration 4.5. Status and User I/O Elements 4.6. Interfaces and Ports 4.7. HiLo Daughter Cards 4.8. Clocks 4.9. Power
4.6. Interfaces and Ports x
4.6.1. PCI Express 4.6.2. Memory Interface 4.6.3. High Bandwidth Memory (HBM2) 4.6.4. QSFP 4.6.5. I2C Flash Memory
4.6.2. Memory Interface x
4.6.2.1. On-board DDR4 Memory Interface 4.6.2.2. DDR4/DDR-T DIMM Memory Interface 4.6.2.3. HiLo Memory Interface
4.7. HiLo Daughter Cards x
4.7.1. DDR4 4.7.2. QDR-IV
4.9. Power x
4.9.1. Power Guidelines 4.9.2. Power Distribution System 4.9.3. Power Sequence 4.9.4. Power Measurement 4.9.5. Power Fast Discharging 4.9.6. Thermal Limitations and Protection 4.9.7. Cooling Design 4.9.8. Mechanical Information 4.9.9. Top Cover Removal
5. Board Test System x
5.1. Preparing the Board Running the Board Test System 5.3. Using the Board Test System
5.3. Using the Board Test System x
5.3.1. The Configure Menu 5.3.2. The Sys Info Tab 5.3.3. The QSFP Tab 5.3.4. The PCIE Tab 5.3.5. The Component DDR4 Tab 5.3.6. The HiLo DDR4 Tab 5.3.7. The DDR4 Dimm Tab 5.3.8. The HBM2 Top Tab 5.3.9. The HBM2 Bottom Tab 5.3.10. Power Monitor 5.3.11. Clock Controller
A. Additional Information x
A.1. Add SmartVID settings in the QSF file A.2. Safety and Regulatory Information A.3. Compliance and Conformity Statement
A.2. Safety and Regulatory Information x
A.2.1. Safety Warnings A.2.2. Safety Cautions
B. Revision History x
B.1. Revision History
1. Overview
2. Getting Started
3. Development Kit Setup
4. Development Kit Components
5. Board Test System
A. Additional Information
B. Revision History

A.1. Add SmartVID settings in the QSF file

Intel® Stratix® 10 FPGA silicon assembled on the Intel® Stratix® 10 MX FPGA Development Kit enables SmartVID feature by default.

You may encounter the following error message when you switch from using the example design to your own design:

Error(19192): File <filename>.sof is incomplete - Power management settings are not set up appropriately on VID part"

To prevent Intel® Quartus® Prime from generating an error message due to incomplete SmartVID settings, you must put constraints listed below into the Intel® Quartus® Prime project QSF file.

Open your Intel® Quartus® Prime project QSF file, copy and paste the constraints listed below in the QSF file.

Before, you compile your project with correct SmartVID settings, ensure that there are no other similar settings with different values.

Constraints

set_global_assignment -name VID_OPERATION_MODE "PMBUS MASTER"
set_global_assignment -name USE_PWRMGT_SCL SDM_IO14
set_global_assignment -name USE_PWRMGT_SDA SDM_IO11
set_global_assignment -name USE_CONF_DONE SDM_IO16
set_global_assignment -name USE_INIT_DONE SDM_IO0
set_global_assignment -name PWRMGT_BUS_SPEED_MODE "100 KHZ"
set_global_assignment -name PWRMGT_SLAVE_DEVICE0_ADDRESS 47
set_global_assignment -name PWRMGT_PAGE_COMMAND_ENABLE ON

The Intel® Stratix® 10 device family offers SmartVID standard power devices in all speed grades. Lower power fixed-voltage devices are also available in all speed grades except for the fastest speed grade. Please refer to Intel Stratix 10 Power Management User Guide for additional information.

Related Information
Level Two Title