Intel® Arria® 10 FPGA Development Kit User Guide

Download PDF
ID 683526
Date 1/13/2024
Public
Document Table of Contents
Document Table of Contents x
1. Intel® Arria® 10 FPGA Development Kit Overview 2. Getting Started 3. Development Board Setup 4. Board Test System 5. Board Update Portal 6. Board Components A. Additional Information
1. Intel® Arria® 10 FPGA Development Kit Overview x
1.1. General Description 1.2. Recommended Operating Conditions 1.3. Handling the Board
2. Getting Started x
2.1. Installing the Subscription Edition Software 2.2. Development Kit Package 2.3. Installing the USB-Blaster Driver
2.1. Installing the Subscription Edition Software x
2.1.1. Activating Your License
3. Development Board Setup x
3.1. Applying Power to the Board 3.2. Default Switch and Jumper Settings 3.3. Default Switch and Resistor Settings 3.4. Factory Reset
4. Board Test System x
4.1. Preparing the Board 4.2. Running the Board Test System 4.3. Version Selector 4.4. Using the Board Test System
4.4. Using the Board Test System x
4.4.1. Using the Configure Menu 4.4.2. The System Info Tab 4.4.3. The GPIO Tab 4.4.4. The Flash Tab 4.4.5. The XCVR Tab 4.4.6. The PCIe Tab 4.4.7. The FMC A Tab 4.4.8. The FMC B Tab 4.4.9. The DDR3 Tab 4.4.10. The DDR4 Tab 4.4.11. The Power Monitor 4.4.12. The Clock Control
5. Board Update Portal x
5.1. Connecting to the Board Update Portal Web Page
5.1. Connecting to the Board Update Portal Web Page x
5.1.1. Using the Board Update Portal to Update User Designs
6. Board Components x
6.1. Board Overview 6.2. MAX V CPLD System Controller 6.3. FPGA Configuration 6.4. Status Elements 6.5. User Input/Output 6.6. Clock Circuitry 6.7. Components and Interfaces 6.8. Memory 6.9. Board Power Supply 6.10. Daughtercards
6.3. FPGA Configuration x
6.3.1. Configuring the FPGA Using Programmer
6.5. User Input/Output x
6.5.1. User-Defined Push Buttons 6.5.2. User-Defined DIP Switch 6.5.3. User-Defined LEDs 6.5.4. Character LCD 6.5.5. DisplayPort 6.5.6. SDI Video Input/Output Ports
6.6. Clock Circuitry x
6.6.1. On-Board Oscillators 6.6.2. Off-Board Clock I/O
6.7. Components and Interfaces x
6.7.1. PCI Express 6.7.2. 10/100/1000 Ethernet PHY 6.7.3. HiLo External Memory Interface 6.7.4. FMC 6.7.5. QSFP 6.7.6. SFP+ 6.7.7. I2C
6.8. Memory x
6.8.1. Flash 6.8.2. Programming the Flash Using Intel® Quartus® Prime Programmer
6.9. Board Power Supply x
6.9.1. Power Distribution System 6.9.2. Power Measurement
6.10. Daughtercards x
6.10.1. External Memory Interface
6.10.1. External Memory Interface x
6.10.1.1. DDR3L 6.10.1.2. DDR4 6.10.1.3. RLDRAM 3 6.10.1.4. QDR-IV 6.10.1.5. FMC Loopback Card
6.10.1.5. FMC Loopback Card x
6.10.1.5.1. High Pin Count (HBC) 6.10.1.5.2. Low Pin Count (LPC)
A. Additional Information x
A.1. Document Revision History for the Intel® Arria® 10 FPGA Development Kit User Guide A.2. Compliance and Conformity Statements
A.2. Compliance and Conformity Statements x
A.2.1. CE EMI Conformity Caution
1. Intel® Arria® 10 FPGA Development Kit Overview
2. Getting Started
3. Development Board Setup
4. Board Test System
5. Board Update Portal
6. Board Components
A. Additional Information

5.1.1. Using the Board Update Portal to Update User Designs

The Board Update Portal allows you to write new designs to the user portion of the flash memory. Designs must be in the Nios II Flash Programmer File (.flash) format.

Design files available from the Intel® Arria® 10 GX FPGA Development Kit page include .flash files. You can also create .flash files from your own custom designs.

To upload a design over the network into the user portion of the flash memory on your board, perform the following steps:

  1. Perform the steps in “Connecting to the Board Update Portal Web Page” section to access the Board Update Portal web page.
  2. In the Hardware File Name field specify the .flash file that you either downloaded from the Intel® website or created on your own. If there is a software component to the design, specify it in the same manner using the Software File Name field or otherwise leave the field blank.
  3. Click Upload. The progress bar indicates the percent complete. The file will take about 20 seconds to upload.
  4. To configure the FPGA with the new design after the flash memory upload process is complete, set SW6.4 to the OFF position.

As long as you don’t overwrite the factory image in the flash memory device, you can continue to use the Board Update Portal to write new designs to the user portion of the flash memory. If you do overwrite the factory image, you can restore it by following the instructions in the “Factory Reset” section.

Related Information
Level Two Title