AN 737: SEU Detection and Recovery in Intel® Arria® 10 Devices

Download PDF
ID 683064
Date 10/21/2021
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Intel® Quartus® Prime Software SEU FIT Reports 3. Intel® Arria® 10 Error Detection and Correction Feature Architecture 4. Guidelines for Error Detection CRC and Error Correction Feature 5. Guidelines for Embedded Memory ECC Feature 6. Intel® Arria® 10 EDCRC Reference Design 7. Implementing ECC Feature in Intel® Arria® 10 ROM Design 8. Modifying Single-Device .jam Files for Use in a Multi-Device JTAG Chain 9. Document Revision History for AN 737: SEU Detection and Recovery in Intel® Arria® 10 Devices
2. Intel® Quartus® Prime Software SEU FIT Reports x
2.1. Enabling the Projected SEU FIT by Component Usage Report 2.2. SEU FIT Parameters Report 2.3. Projected SEU FIT by Component Usage Report
2.3. Projected SEU FIT by Component Usage Report x
2.3.1. Component FIT Rates 2.3.2. Raw FIT 2.3.3. Utilized FIT 2.3.4. Mitigated FIT 2.3.5. Architectural Vulnerability Factor
2.3.3. Utilized FIT x
2.3.3.1. Comparing .smh Critical Bits Report to Utilized Bit Count 2.3.3.2. Considerations for Small Designs
3. Intel® Arria® 10 Error Detection and Correction Feature Architecture x
3.1. Error Detection and Correction for CRAM 3.2. Memory Blocks Error Correction Code Support
3.1. Error Detection and Correction for CRAM x
3.1.1. Error Detection Cyclic Redundancy Check 3.1.2. Recovering from CRC Errors
3.1.1. Error Detection Cyclic Redundancy Check x
3.1.1.1. Column-Based and Frame-Based Check-Bits 3.1.1.2. Error Message Register
4. Guidelines for Error Detection CRC and Error Correction Feature x
4.1. Error Detection 4.2. Enabling Error Correction (Internal Scrubbing) 4.3. Interpreting CRC_ERROR
4.1. Error Detection x
4.1.1. Enabling Error Detection 4.1.2. Reading EMR
4.1.1. Enabling Error Detection x
4.1.1.1. Enabling the Error Detection CRC_ERROR Pin
4.1.2. Reading EMR x
4.1.2.1. Reading EMR using EMR Unloader IP Core 4.1.2.2. Reading EMR using HPS 4.1.2.3. Reading EMR using JTAG Interface
4.3. Interpreting CRC_ERROR x
4.3.1. CRC_ERROR Pin Behavior 4.3.2. Correctable and Uncorrectable Error
6. Intel® Arria® 10 EDCRC Reference Design x
6.1. System Requirements 6.2. Creating Intel® Arria® 10 SEU Fault Injection and Hierarchy Tagging Design with Qsys 6.3. Design Testing with Fault Injection Debugger
6.2. Creating Intel® Arria® 10 SEU Fault Injection and Hierarchy Tagging Design with Qsys x
6.2.1. Starting Intel® Quartus® Prime Software and Opening the Reference Design Project 6.2.2. Creating New Qsys System 6.2.3. Generating Qsys System 6.2.4. Integrating Qsys System into Quartus Prime Project
6.2.2. Creating New Qsys System x
6.2.2.1. Specifying Target FPGA and Clock Settings 6.2.2.2. Adding Altera IOPLL IP Core 6.2.2.3. Adding EMR Unloader IP Core 6.2.2.4. Adding Advance SEU Detection IP Core 6.2.2.5. Adding Fault Injection IP Core 6.2.2.6. Adding Avalon-ST Splitter 6.2.2.7. Adding Serial Flash Controller
6.2.4. Integrating Qsys System into Quartus Prime Project x
6.2.4.1. Generating In-System Source and Probe IP Core 6.2.4.2. Quartus Prime Project Settings 6.2.4.3. Assigning ASD Regions 6.2.4.4. Assigning FPGA Pin Location 6.2.4.5. Compiling the Project
6.3. Design Testing with Fault Injection Debugger x
6.3.1. Converting .sof File and .smh File to .jic File 6.3.2. Programing .jic File into EPCQ-L 6.3.3. Launching Signal Tap Logic Analyzer 6.3.4. Configuring Intel® Arria® 10 and Reading .smh File with Fault Injection Debugger 6.3.5. Injecting Error with Fault Injection Debugger
7. Implementing ECC Feature in Intel® Arria® 10 ROM Design x
7.1. Examples of Error Detection and Correction
1. Overview
2. Intel® Quartus® Prime Software SEU FIT Reports
3. Intel® Arria® 10 Error Detection and Correction Feature Architecture
4. Guidelines for Error Detection CRC and Error Correction Feature
5. Guidelines for Embedded Memory ECC Feature
6. Intel® Arria® 10 EDCRC Reference Design
7. Implementing ECC Feature in Intel® Arria® 10 ROM Design
8. Modifying Single-Device .jam Files for Use in a Multi-Device JTAG Chain
9. Document Revision History for AN 737: SEU Detection and Recovery in Intel® Arria® 10 Devices

6.2.2.7. Adding Serial Flash Controller

You must use the Serial Flash Controller IP core to access to the EPCQ-L1024 that stores the SMH file in this reference design. The ASD IP core reads the SMH data from EPCQ-L1024 via Serial Flash Controller IP core. To add the Serial Flash Controller, perform the following steps:

  1. On the IP Catalog tab, expand Basic Functions, expand Configuration and Programming, and then click Altera Serial Flash Controller.
  2. Click Add. The Altera Serial Flash Controller parameter editor appears. Set the parameters as the follows:
    1. On Configuration device type list, select EPCQL1024.
    2. On Choose I/O mode, select QUAD.
    3. On Number of Chip Selects used list, select 1.
  3. Click Finish to return to Qsys. On the System Content tab, an instance of the epcq_controller_0 appears in the system contents table.
  4. Connect outclk1 port of iopll_0 to clock_sink port of epcq_controller_0.
    Note: The Fmax for Serial Flash Controller is 25MHz
  5. Connect clk_reset port of clk_0 clock source to reset port of epcq_controller_0.
  6. Connect asd_sp_master port of adv_seu_detection_0 to avl_mem port of epcq_controller_0.
Level Two Title