AN 737: SEU Detection and Recovery in Intel® Arria® 10 Devices

Download PDF
ID 683064
Date 10/21/2021
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Intel® Quartus® Prime Software SEU FIT Reports 3. Intel® Arria® 10 Error Detection and Correction Feature Architecture 4. Guidelines for Error Detection CRC and Error Correction Feature 5. Guidelines for Embedded Memory ECC Feature 6. Intel® Arria® 10 EDCRC Reference Design 7. Implementing ECC Feature in Intel® Arria® 10 ROM Design 8. Modifying Single-Device .jam Files for Use in a Multi-Device JTAG Chain 9. Document Revision History for AN 737: SEU Detection and Recovery in Intel® Arria® 10 Devices
2. Intel® Quartus® Prime Software SEU FIT Reports x
2.1. Enabling the Projected SEU FIT by Component Usage Report 2.2. SEU FIT Parameters Report 2.3. Projected SEU FIT by Component Usage Report
2.3. Projected SEU FIT by Component Usage Report x
2.3.1. Component FIT Rates 2.3.2. Raw FIT 2.3.3. Utilized FIT 2.3.4. Mitigated FIT 2.3.5. Architectural Vulnerability Factor
2.3.3. Utilized FIT x
2.3.3.1. Comparing .smh Critical Bits Report to Utilized Bit Count 2.3.3.2. Considerations for Small Designs
3. Intel® Arria® 10 Error Detection and Correction Feature Architecture x
3.1. Error Detection and Correction for CRAM 3.2. Memory Blocks Error Correction Code Support
3.1. Error Detection and Correction for CRAM x
3.1.1. Error Detection Cyclic Redundancy Check 3.1.2. Recovering from CRC Errors
3.1.1. Error Detection Cyclic Redundancy Check x
3.1.1.1. Column-Based and Frame-Based Check-Bits 3.1.1.2. Error Message Register
4. Guidelines for Error Detection CRC and Error Correction Feature x
4.1. Error Detection 4.2. Enabling Error Correction (Internal Scrubbing) 4.3. Interpreting CRC_ERROR
4.1. Error Detection x
4.1.1. Enabling Error Detection 4.1.2. Reading EMR
4.1.1. Enabling Error Detection x
4.1.1.1. Enabling the Error Detection CRC_ERROR Pin
4.1.2. Reading EMR x
4.1.2.1. Reading EMR using EMR Unloader IP Core 4.1.2.2. Reading EMR using HPS 4.1.2.3. Reading EMR using JTAG Interface
4.3. Interpreting CRC_ERROR x
4.3.1. CRC_ERROR Pin Behavior 4.3.2. Correctable and Uncorrectable Error
6. Intel® Arria® 10 EDCRC Reference Design x
6.1. System Requirements 6.2. Creating Intel® Arria® 10 SEU Fault Injection and Hierarchy Tagging Design with Qsys 6.3. Design Testing with Fault Injection Debugger
6.2. Creating Intel® Arria® 10 SEU Fault Injection and Hierarchy Tagging Design with Qsys x
6.2.1. Starting Intel® Quartus® Prime Software and Opening the Reference Design Project 6.2.2. Creating New Qsys System 6.2.3. Generating Qsys System 6.2.4. Integrating Qsys System into Quartus Prime Project
6.2.2. Creating New Qsys System x
6.2.2.1. Specifying Target FPGA and Clock Settings 6.2.2.2. Adding Altera IOPLL IP Core 6.2.2.3. Adding EMR Unloader IP Core 6.2.2.4. Adding Advance SEU Detection IP Core 6.2.2.5. Adding Fault Injection IP Core 6.2.2.6. Adding Avalon-ST Splitter 6.2.2.7. Adding Serial Flash Controller
6.2.4. Integrating Qsys System into Quartus Prime Project x
6.2.4.1. Generating In-System Source and Probe IP Core 6.2.4.2. Quartus Prime Project Settings 6.2.4.3. Assigning ASD Regions 6.2.4.4. Assigning FPGA Pin Location 6.2.4.5. Compiling the Project
6.3. Design Testing with Fault Injection Debugger x
6.3.1. Converting .sof File and .smh File to .jic File 6.3.2. Programing .jic File into EPCQ-L 6.3.3. Launching Signal Tap Logic Analyzer 6.3.4. Configuring Intel® Arria® 10 and Reading .smh File with Fault Injection Debugger 6.3.5. Injecting Error with Fault Injection Debugger
7. Implementing ECC Feature in Intel® Arria® 10 ROM Design x
7.1. Examples of Error Detection and Correction
1. Overview
2. Intel® Quartus® Prime Software SEU FIT Reports
3. Intel® Arria® 10 Error Detection and Correction Feature Architecture
4. Guidelines for Error Detection CRC and Error Correction Feature
5. Guidelines for Embedded Memory ECC Feature
6. Intel® Arria® 10 EDCRC Reference Design
7. Implementing ECC Feature in Intel® Arria® 10 ROM Design
8. Modifying Single-Device .jam Files for Use in a Multi-Device JTAG Chain
9. Document Revision History for AN 737: SEU Detection and Recovery in Intel® Arria® 10 Devices

6.2.2.6. Adding Avalon-ST Splitter

EMR Unloader core sends the EMR data to the downstream IP cores with Avalon-ST protocol. Both ASD IP core and Fault Injection IP core require EMR data from EMR Unloader core. You need to instantiate the Avalon-ST Splitter to distribute the EMR data from EMR Unloader to ASD IP core and Fault Injection IP core. To add the Avalon-ST Splitter, perform the following steps:

  1. On the IP Catalog tab, expand Basic Functions, expand Bridges and Adaptors, expand Streaming, and click Avalon-ST Splitter.
  2. Click Add. The Avalon-ST Splitter parameter editor appears.
  3. Set NUMBER_OF_OUTPUTS to 3.
  4. Check only USE_VALID, USE_ERROR and USE_DATA, uncheck all other check boxes.
  5. Set DATA_WIDTH to 119.
  6. Set ERROR_WIDTH to 1.
  7. Set BITS_PER_SYMBOL to 119.
  8. Click Finish to return to Qsys. On the System Contents tab, an instance of the st_splitter_0 appears in the system contents table.
  9. Connect clk_reset port of the clk_0 clock source to reset port of st_splitter_0.
  10. Connect intosc port of the fault_injection_0 to clk port of st_splitter_0.
  11. Connect avst_emr_src port of emr_unloader2_0 to in port of st_splitter_0.
  12. Connect out0 port of st_splitter_0 to avst_emr_snk port of adv_seu_detection_0.
  13. Connect out1 port of st_splitter_0 to avst_emr_snk port of fault_injection_0.
  14. Double click the out2 port of the st_splitter_0 at Export column to export it for external access, leave the name default. This port will be used for Signal Tap purpose to read the EMR value after the fault injection.
Level Two Title