Intel® Arria® 10 Avalon® Streaming with SR-IOV IP for PCIe* User Guide

Download PDF
ID 683686
Date 1/11/2022
Public
Document Table of Contents
Document Table of Contents x
1. Datasheet 2. Getting Started with the SR-IOV Design Example 3. Parameter Settings 4. Physical Layout 5. Interfaces and Signal Descriptions 6. Registers 7. Programming and Testing SR-IOV Bridge MSI Interrupts 8. Error Handling 9. IP Core Architecture 10. Design Implementation 11. Debugging 12. Document Revision History A. Transaction Layer Packet (TLP) Header Formats B. Intel® Arria® 10 Avalon-ST with SR-IOV Interface for PCIe Solutions User Guide Archive
1. Datasheet x
1.1. Intel® Arria® 10 Avalon® -ST Interface with SR-IOV for PCI Express* Datasheet 1.2. Release Information 1.3. Device Family Support 1.4. Debug Features 1.5. IP Core Verification 1.6. Performance and Resource Utilization 1.7. Recommended Speed Grades for SR-IOV Interface
1.1. Intel® Arria® 10 Avalon® -ST Interface with SR-IOV for PCI Express* Datasheet x
1.1.1. SR-IOV Features
1.5. IP Core Verification x
1.5.1. Compatibility Testing Environment
2. Getting Started with the SR-IOV Design Example x
2.1. Directory Structure for Intel® Arria® 10 SR-IOV Design Example 2.2. Design Components for the SR-IOV Design Example 2.3. Generating the SR-IOV Design Example 2.4. Compiling and Simulating the Design for SR-IOV
3. Parameter Settings x
3.1. Parameters 3.2. Intel® Arria® 10 Avalon-ST Settings 3.3. Intel® Arria® 10 SR-IOV System Settings 3.4. Base Address Register (BAR) Settings 3.5. SR-IOV Device Identification Registers 3.6. Intel® Arria® 10 Interrupt Capabilities 3.7. Physical Function TLP Processing Hints (TPH) 3.8. Address Translation Services (ATS) 3.9. PCI Express and PCI Capabilities Parameters 3.10. PHY Characteristics 3.11. Example Designs
3.9. PCI Express and PCI Capabilities Parameters x
3.9.1. PCI Express and PCI Capabilities 3.9.2. Error Reporting 3.9.3. Link Capabilities 3.9.4. Slot Capabilities 3.9.5. Power Management
4. Physical Layout x
4.1. Hard IP Block Placement In Intel® Cyclone® 10 GX Devices 4.2. Hard IP Block Placement In Intel® Arria® 10 Devices 4.3. Channel and Pin Placement for the Gen1, Gen2, and Gen3 Data Rates 4.4. Channel Placement and fPLL and ATX PLL Usage for the Gen3 Data Rate 4.5. PCI Express Gen3 Bank Usage Restrictions
5. Interfaces and Signal Descriptions x
5.1. Avalon-ST TX Interface 5.2. Component-Specific Avalon-ST Interface Signals 5.3. Avalon-ST RX Interface 5.4. BAR Hit Signals 5.5. Configuration Status Interface 5.6. Clock Signals 5.7. Function-Level Reset (FLR) Interface 5.8. SR-IOV Interrupt Interface 5.9. Configuration Extension Bus (CEB) Interface 5.10. Implementing MSI-X Interrupts 5.11. Control Shadow Interface 5.12. Local Management Interface (LMI) Signals 5.13. Reset, Status, and Link Training Signals 5.14. Hard IP Reconfiguration Interface 5.15. Serial Data Signals 5.16. Test Signals 5.17. PIPE Interface Signals 5.18. Intel® Arria® 10 Development Kit Conduit Interface
5.9. Configuration Extension Bus (CEB) Interface x
5.9.1. Vital Product Data (VPD) Capability
5.9.1. Vital Product Data (VPD) Capability x
5.9.1.1. Determine the Pointer Address of an External Capability Register 5.9.1.2. VPD Capability Implementation
6. Registers x
6.1. Addresses for Physical and Virtual Functions 6.2. Correspondence between Configuration Space Registers and the PCIe Specification 6.3. PCI and PCI Express Configuration Space Registers 6.4. MSI Registers 6.5. MSI-X Capability Structure 6.6. Power Management Capability Structure 6.7. PCI Express Capability Structure 6.8. Advanced Error Reporting (AER) Enhanced Capability Header Register 6.9. Uncorrectable Error Status Register 6.10. Uncorrectable Error Mask Register 6.11. Uncorrectable Error Severity Register 6.12. Correctable Error Status Register 6.13. Correctable Error Mask Register 6.14. Advanced Error Capabilities and Control Register 6.15. Header Log Registers 0-3 6.16. SR-IOV Virtualization Extended Capabilities Registers 6.17. Virtual Function Registers
6.3. PCI and PCI Express Configuration Space Registers x
6.3.1. Type 0 Configuration Space Registers 6.3.2. PCI and PCI Express Configuration Space Register Content 6.3.3. Interrupt Line and Interrupt Pin Register
6.16. SR-IOV Virtualization Extended Capabilities Registers x
6.16.1. SR-IOV Virtualization Extended Capabilities Registers Address Map 6.16.2. ARI Enhanced Capability Header 6.16.3. SR-IOV Enhanced Capability Registers 6.16.4. Initial VFs and Total VFs Registers 6.16.5. VF Device ID Register 6.16.6. Page Size Registers 6.16.7. VF Base Address Registers (BARs) 0-5 6.16.8. Secondary PCI Express Extended Capability Header 6.16.9. Lane Status Registers 6.16.10. Transaction Processing Hints (TPH) Requester Enhanced Capability Header
7. Programming and Testing SR-IOV Bridge MSI Interrupts x
7.1. Setting Up and Verifying MSI Interrupts 7.2. Masking MSI Interrupts 7.3. Dropping a Pending MSI Interrupt
8. Error Handling x
8.1. Physical Layer Errors 8.2. Data Link Layer Errors 8.3. Transaction Layer Errors 8.4. Error Reporting and Data Poisoning 8.5. Uncorrectable and Correctable Error Status Bits
9. IP Core Architecture x
9.1. PCI Express Protocol Stack 9.2. Data Link Layer 9.3. Physical Layer 9.4. Top-Level Interfaces 9.5. Intel® Arria® 10 Hard IP for PCI Express with Single-Root I/O Virtualization (SR-IOV)
9.4. Top-Level Interfaces x
9.4.1. Avalon-ST Interface 9.4.2. Clocks and Reset 9.4.3. Interrupts 9.4.4. PIPE
10. Design Implementation x
10.1. Making Pin Assignments to Assign I/O Standard to Serial Data Pins 10.2. Recommended Reset Sequence to Avoid Link Training Issues 10.3. SDC Timing Constraints
11. Debugging x
11.1. Setting Up Simulation 11.2. Simulation Fails To Progress Beyond Polling.Active State 11.3. Hardware Bring-Up Issues 11.4. Link Training 11.5. Creating a Signal Tap Debug File to Match Your Design Hierarchy 11.6. Use Third-Party PCIe Analyzer 11.7. BIOS Enumeration Issues
11.1. Setting Up Simulation x
11.1.1. Changing Between Serial and PIPE Simulation 11.1.2. Using the PIPE Interface for Gen1 and Gen2 Variants 11.1.3. Viewing the Important PIPE Interface Signals 11.1.4. Disabling the Scrambler for Gen1 and Gen2 Simulations 11.1.5. Disabling 8B/10B Encoding and Decoding for Gen1 and Gen2 Simulations
12. Document Revision History x
12.1. Document Revision History for the Intel® Arria® 10 Avalon® Streaming with SR-IOV IP for PCIe* User Guide
A. Transaction Layer Packet (TLP) Header Formats x
A.1. TLP Packet Formats without Data Payload A.2. TLP Packet Formats with Data Payload
1. Datasheet
2. Getting Started with the SR-IOV Design Example
3. Parameter Settings
4. Physical Layout
5. Interfaces and Signal Descriptions
6. Registers
7. Programming and Testing SR-IOV Bridge MSI Interrupts
8. Error Handling
9. IP Core Architecture
10. Design Implementation
11. Debugging
12. Document Revision History
A. Transaction Layer Packet (TLP) Header Formats
B. Intel® Arria® 10 Avalon-ST with SR-IOV Interface for PCIe Solutions User Guide Archive

6.4. MSI Registers

Figure 44. MSI Register Byte Address Offsets and Layout
Table 46.  MSI Control Register - 0x050

Bits

Register Description

Default Value

Access

[31:25]

Not implemented

0

RO

[24]

Per-Vector Masking Capable. This bit is hardwired to 1. The design always supports per-vector masking of MSI interrupts.

1

RO

[23]

64-bit Addressing Capable. When set, the device is capable of using 64-bit addresses for MSI interrupts.

Set in Platform Designer

RO

[22:20]

Multiple Message Enable. This field defines the number of interrupt vectors for this function. The following encodings are defined:

  • 3'b000: 1 vector
  • 3'b001: 2 vectors
  • 3'b010: 4 vectors
  • 3'b011: 8 vectors
  • 3'b100: 16 vectors
  • 3'b101: 32 vectors

The Multiple Message Capable field specifies the maximum value allowed.

0

RW

[19:17]

Multiple Message Capable. Defines the maximum number of interrupt vectors the function is capable of supporting. The following encodings are defined:

  • 3'b000: 1 vector
  • 3'b001: 2 vectors
  • 3'b010: 4 vectors
  • 3'b011: 8 vectors
  • 3'b100: 16 vectors
  • 3'b101: 32 vectors

Set inPlatform Designer

RO

[16]

MSI Enable. This bit must be set to enable the MSI interrupt generation.

0

RW

[15:8]

Next Capability Pointer. Points to either MSI-X or Power Management Capability.

0x68 or 0x78

RO

[7:0]

Capability ID. PCI-SIG assigns this value.

0x05

RO

Table 47.  MSI Message Address Registers - 0x054 and 0x058

Bits

Register Description

Default Value

Access

[1:0]

The two least significant bits of the memory address. These are hardwired to 0 to align the memory address on a Dword boundary.

0

RO

[31:2]

Lower address for the MSI interrupt.

0

RW

[31:0]

Upper 32 bits of the 64-bit address to be used for the MSI interrupt. If the 64-bit Addressing Capable bit in the MSI Control register is set to 1, this value is concatenated with the lower 32-bits to form the memory address for the MSI interrupt. When the 64-bit Addressing Capable bit is 0, this register always reads as 0.

0

RW

Table 48.  MSI Message Data Register - 0x058 or 0x05C RegisterIf the 64-bit Addressing Capable bit in the MSI Control Register is set to 1, this register is at address 0x05C. Otherwise, it is at address 0x058.

Bits

Register Description

Default Value

Access

[15:0]

Data for MSI Interrupts generated by this function. This base value is written to Root Port memory to signal an MSI interrupt. When one MSI vector is allowed, this value is used directly. When 2 MSI vectors are allowed, the upper 15 bits are used. And, the least significant bit indicates the interrupt number. When 4 MSI vectors are allowed, the lower 2 bits indicate the interrupt number, and so on.

0

RW

[31:16]

Reserved

0

RO

Table 49.  MSI Mask Register - 0x05C (32-bit addressing) or 0x060 (64-bit addressing)

If the 64-bit Addressing Capable bit in the MSI Control Register is set to 1, this register is at address 0x060. Otherwise, it is at 0x05C.

Bits

Register Description

Default Value

Access

31:0

Mask bits for MSI interrupts. The number of implemented bits depends on the number of MSI vectors configured. When one MSI vectors is used , only bit 0 is RW. The other bits read as zeros. When two MSI vectors are used, bits [1:0] are RW, and so on. A one in a bit position masks the corresponding MSI interrupt.

See description

0

Table 50.  Pending Bits for MSI Interrupts Register - 0x060 (32-bit addressing) or 0x064 (64-bit addressing)

If the 64-bit Addressing Capable bit in the MSI Control Register is set to 1, this register is at address 0x064. Otherwise, it is at 0x060.

Bits

Register Description

Default Value

Access

31:0

Pending bits for MSI interrupts. A 1 in a bit position indicated the corresponding MSI interrupt is pending in the core. The number of implemented bits depends on the number of MSI vectors configured. When 1 MSI vectors is used, only bit 0 is RW. The other bits read as zeros. When 2 MSI vectors are used, bits [1:0] are RW, and so on.

RO

0

Related Information
Level Two Title