Intel® Stratix® 10 SX SoC Development Kit User Guide

Download PDF
ID 683303
Date 6/02/2023
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Development Kit Components 5. Board Test System A. Additional Information B. Revision History
1. Overview x
1.1. General Development Kit Description 1.2. Recommended Operating Conditions 1.3. Handling the Development Kit
2. Getting Started x
2.1. Installing Quartus Prime Software 2.2. Installing the Intel® FPGA Download Cable 2.3. Installing the Intel SoC Embedded Development Suite (EDS) 2.4. Installing the Intel® Stratix® 10 SX SoC Development Kit Package
3. Development Kit Setup x
3.1. Inspect the Development Kit 3.2. Default Setup of the Development Kit 3.3. Intel® MAX® 10 System Controller Updates
4. Development Kit Components x
4.1. Development Kit Feature Summary 4.2. Board Components 4.3. Intel® Stratix® 10 SoC Device Overview 4.4. Intel® MAX® 10 System Controller Overview 4.5. FPGA Configuration 4.6. General User Input/Output 4.7. Connectors and Interfaces 4.8. Daughter Cards 4.9. System Memory 4.10. System Power
4.7. Connectors and Interfaces x
4.7.1. PCIe* Slot 4.7.2. ZQSFP+ 4.7.3. SFP+ 4.7.4. HDMI 4.7.5. SDI Port 4.7.6. MXP 4.7.7. Intel® FPGA Download Cable Direct Port (Debug Port) 4.7.8. FMC+ A/B Slot 4.7.9. FMC+ A/B LVDS Interfaces (LPC Pins) 4.7.10. LMK05028 Jitter Attenuator 4.7.11. FPGA-IOMAX10 Interface
4.8. Daughter Cards x
4.8.1. HPS IO-48 OOBE Daughter Card 4.8.2. HPS IO-48 NAND Flash Daughter Card 4.8.3. HPS Boot Flash Card
4.8.3. HPS Boot Flash Card x
4.8.3.1. Boot QSPI Flash Daughter Card 4.8.3.2. Boot MicroSD Daughter Card 4.8.3.3. Boot eMMC Daughter Card
4.9. System Memory x
4.9.1. FPGA Memory (DDR4 SO-DIMM) 4.9.2. HPS Memory (External 4 GB HILO x72 DDR4 ) 4.9.3. HPS I2C Interface
4.10. System Power x
4.10.1. Power Supply Options 4.10.2. Power Sequence 4.10.3. Power Distribution Network
5. Board Test System x
5.1. Preparing the Board 5.2. Running the BTS 5.3. Using the BTS
5.3. Using the BTS x
5.3.1. The Configure Menu 5.3.2. The GPIO Tab 5.3.3. The QSFP/SFP Tab 5.3.4. The PCIE Tab 5.3.5. The MXP Tab 5.3.6. The FMCA Tab 5.3.7. The FMCB Tab 5.3.8. The DDR4 Tab 5.3.9. Power Monitor 5.3.10. The Clock Control F_vco Registers Frequency (MHz) Default Read Set
A. Additional Information x
A.1. Modify the Intel® Stratix® 10 SX SoC Development Kit to use a battery for the BBRAM A.2. Modify the Intel® Stratix® 10 SX SoC Development Kit HPS DDR4 memory width and ECC configuration using the Golden Hardware Reference Design project A.3. Safety and Regulatory Information A.4. Compliance Information
A.3. Safety and Regulatory Information x
A.3.1. Safety Warnings A.3.2. Safety Cautions
A.4. Compliance Information x
A.4.1. Compliance and Conformity Statements
B. Revision History x
B.1. Revision History
1. Overview
2. Getting Started
3. Development Kit Setup
4. Development Kit Components
5. Board Test System
A. Additional Information
B. Revision History

5.3.10. The Clock Control

The Clock Control application sets the three programmable oscillators to any frequency between 10 MHz and 810 MHz. The frequencies support eight digits of precision to the right of the decimal point.

The Clock Control communicates with the Intel® MAX® 10 device on the board through the JTAG bus. The programmable oscillators are connected to the Intel® MAX® 10 device through a 2-wire serial bus.

Figure 44. Clock Control

The Si5338 tab and Si5341 tab displays the same GUI controls for each clock generators. Each tab allows for separate control. The Si5338 is capable of synthesizing four independent user-programmble clock frequencies up t0 350 MHz and select frequencies up to 710 MHz.

F_vco

Displays the generating signal value of the voltage-controlled oscillator.

Registers

Display the current frequency of the clock.

Frequency (MHz)

Allows you to specify the frequency of the clock.

Default

Sets the frequency for the oscillator associated with the active tab back to its default value. The default is restored by power cycling the board.

Read

Reads the current frequency setting for the oscillator associated with the active tab.

Set

Sets the programmable oscillator frequency for the selected clock to the value in the CLK0 to CLK3 controls for each Si5338. Frequency changes might take several milliseconds to take effect. You might see glitches on the clock during this time. Intel® recommends resetting the FPGA logic after changing frequencies.

Level Two Title