Intel® Stratix® 10 GX Transceiver Signal Integrity Development Kit User Guide

Download PDF
ID 683206
Date 2/21/2023
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Board Setup 4. Board Components 5. System Power 6. Board Test System 7. Board Update Portal A. Additional Information B. Revision History
1. Overview x
1.1. General Board Description 1.2. Recommended Operating Conditions 1.3. Handling the Development Board
2. Getting Started x
2.1. Installing the Quartus Prime software 2.2. Installing the Development Board 2.3. Installing the Intel® FPGA Download Cable Driver
3. Development Board Setup x
3.1. Setting up the Development Board 3.2. Factory Default Switch and Jumper Settings
4. Board Components x
4.1. Board Overview 4.2. Intel® Stratix® 10 GX FPGA 4.3. MAX V CPLD System Controller 4.4. FPGA Configuration 4.5. Status Elements 4.6. Setup Elements 4.7. User Input-Output Components 4.8. Clock Circuits 4.9. Transceiver Channels 4.10. Communication Ports 4.11. Flash Memory
4.4. FPGA Configuration x
4.4.1. FPGA Programming over Embedded Intel® FPGA Download Cable II 4.4.2. FPGA Programming from Flash Memory 4.4.3. FPGA Programming over External Intel® FPGA Download Cable II
4.7. User Input-Output Components x
4.7.1. User-Defined Pushbuttons 4.7.2. User-Defined DIP Switch 4.7.3. User-Defined LEDs 4.7.4. Character LCD
4.8. Clock Circuits x
4.8.1. Transceiver Dedicated Clocks 4.8.2. General-Purpose Clocks 4.8.3. Embedded Intel® FPGA Download Cable II Clock
5. System Power x
5.1. Power Guidelines 5.2. Power Supply 5.3. Power Management 5.4. Power Distribution System 5.5. Thermal Limitations and Protection Guidelines
6. Board Test System x
6.1. Preparing the Board 6.2. Running the Board Test System 6.3. Using the Board Test System
6.3. Using the Board Test System x
6.3.1. The Configure Menu 6.3.2. The System Info Tab 6.3.3. The GPIO Tab 6.3.4. The Flash Tab 6.3.5. The FMCA Tab 6.3.6. The FMCB Tab 6.3.7. The LPBK Tab 6.3.8. The MXP Tab 6.3.9. The SMA Tab 6.3.10. The QSFP and SFP+ Tab 6.3.11. The CFP4 Tab 6.3.12. Power Monitor 6.3.13. Clock Controller
7. Board Update Portal x
7.1. Connecting to the Board Update Portal 7.2. Using the Board Update Portal
A. Additional Information x
A.1. Safety and Regulatory Information A.2. Compliance and Conformity Information
A.1. Safety and Regulatory Information x
A.1.1. Safety Warnings Power Supply Hazardous Voltage Power Connect and Disconnect System Grounding (Earthing) Power Cord Requirements Lightning/Electrical Storm Risk of Fire A.1.2. Safety Cautions
B. Revision History x
B.1. User Guide Revision History
1. Overview
2. Getting Started
3. Development Board Setup
4. Board Components
5. System Power
6. Board Test System
7. Board Update Portal
A. Additional Information
B. Revision History

A.1.1. Safety Warnings

Power Supply Hazardous Voltage

AC mains voltages are present within the power supply assembly. No user serviceable parts are present inside the power supply.

Power Connect and Disconnect

The AC power supply cord is the primary disconnect device from mains (AC power) and used to remove all DC power from the board/system. The socket outlet must be installed near the equipment and must be readily accessible.

System Grounding (Earthing)

To avoid shock, you must ensure that the power cord is connected to a properly wired and grounded receptacle. Ensure that any equipment to which this product will be attached is also connected to properly wired and grounded receptacles.

Power Cord Requirements

The connector that plugs into the wall outlet must be a grounding-type male plug designed for use in your region. It must have marks showing certification by an agency in your region. The connector that plugs into the AC receptacle on the power supply must be an IEC 320, sheet C13, female connector. If the power cord supplied with the system does not meet requirements for use in your region, discard the cord and do not use it with adapters.

Lightning/Electrical Storm

Do not connect/disconnect any cables or perform installation/maintenance of this product during an electrical storm.

Risk of Fire

To reduce the risk of fire, keep all flammable materials a safe distance away from the boards and power supply. You must configure the development kit on a flame retardant surface.

Level Two Title