AN 778: Intel® Stratix® 10 L-Tile/H-Tile Transceiver Usage

Download PDF
ID 683086
Date 6/24/2022
Public
Document Table of Contents
Document Table of Contents x
1. Transceiver Layout 2. Tile Architecture Constraints 3. PCIe Guidelines 4. Document Revision History for AN 778: Intel® Stratix® 10 L-Tile/H-Tile Transceiver Usage
1. Transceiver Layout x
1.1. L-Tile and H-Tile Overview
1.1. L-Tile and H-Tile Overview x
1.1.1. PLLs 1.1.2. Transmitter Clock Network 1.1.3. GXT Clock Network 1.1.4. Calibration
1.1.1. PLLs x
1.1.1.1. ATX PLL 1.1.1.2. fPLL 1.1.1.3. CMU PLL
1.1.2. Transmitter Clock Network x
1.1.2.1. Bonded Transceiver Channels - Guidelines for VCCR_GXB and VCCT_GXB
2. Tile Architecture Constraints x
2.1. Transceiver Channel Placement 2.2. Unsupported Dynamic Reconfiguration Features 2.3. Intel® Stratix® 10 L-Tile Transceiver to H-Tile Transceiver Migration 2.4. Thermal Guidelines
2.1. Transceiver Channel Placement x
2.1.1. Possible Combinations of GX and GXT Channels 2.1.2. GX Channels 2.1.3. GXT Channels 2.1.4. Bonded Channel Placement with Data Rate Change 2.1.5. Reference Clock Guidelines for L-Tile and H-Tile 2.1.6. PLL Placement
2.1.1. Possible Combinations of GX and GXT Channels x
2.1.1.1. Possible Combinations of GX and GXT Channels in H-Tile 2.1.1.2. Possible Combinations of GX and GXT Channels in L-Tile
2.1.2. GX Channels x
2.1.2.1. Non-bonded GX Channels 2.1.2.2. Bonded GX Channels
2.1.6. PLL Placement x
2.1.6.1. ATX PLL – fPLL Spacing Requirements 2.1.6.2. ATX PLL Usage Model When Driving GXT Channels 2.1.6.3. Simplex Channel Merging 2.1.6.4. TX PLL Restrictions when Using PCIe*
3. PCIe Guidelines x
3.1. PCIe Hard IP 3.2. PHY Interface for PCIe Express (PIPE)
3.1. PCIe Hard IP x
3.1.1. Channel Placement for PCIe Hard IP 3.1.2. PLL Placement for PCIe Hard IP 3.1.3. Non-PCIe and PCIe Hard IP Channel Placement in L-Tile and H-Tile
3.2. PHY Interface for PCIe Express (PIPE) x
3.2.1. Channel Placement for PIPE 3.2.2. PLL Placement for PIPE 3.2.3. Non-PCIe and PCIe PIPE Channel Placement in H-Tile 3.2.4. Non-PCIe and PCIe PIPE Channel Placement in L-Tile
1. Transceiver Layout
2. Tile Architecture Constraints
3. PCIe Guidelines
4. Document Revision History for AN 778: Intel® Stratix® 10 L-Tile/H-Tile Transceiver Usage

3.1.3. Non-PCIe and PCIe Hard IP Channel Placement in L-Tile and H-Tile

For OTN or SDI channels that share a tile with active PCI Express interfaces with PCIe Hard IP enabled that are Gen2 or Gen3 capable and configured with more than four lanes (Gen2/3 x8, x16), the maximum data rate is less than 9 Gbps.

Running the OTN or SDI channels within the same tile at data rates faster than 9 Gbps may result in bit errors at the remote OTN or SDI device during PCI Express rate change events (PCIe link training both up and down, during link down and start of link training).

Avoid placing OTN or SDI channels above 9 Gbps in the same tile with PCI Express Hard IP interfaces that are Gen 2 or Gen 3 capable and configured with x8 or x16 lanes, or bring up the PCI Express channels first, followed by the OTN or SDI channels. Transceiver channels that share a tile with active PCI Express interfaces that are only Gen1 capable are not impacted.

Figure 40. Channel Placement for OTN or SDI channel > 9 Gbps and PCIe PIPE Channels in H-Tile
Level Two Title